Skip to main content
Provide the Appliance Model, Symptoms, Service Address, and Access Details. Appointment Requirements Are Confirmed Before Scheduling. Refrigeration Service Planned for the Diagnosed Scope Genuine OEM Parts 365-Day Repair Warranty

Error Codes

Jenn-Air F-E Fault Codes Explained

Jenn-Air ovens use the Whirlpool F#-E# code system, where F identifies the function and E the specific error. Here is what the common ones point to.

Short answer: In the F#-E# system, F1 is control, F2 is keypad, F3 is the oven sensor, and F5 is the door latch. A stuck-key or one-time control fault may clear with a reset, but a sensor or latch fault usually needs a technician. Note the full code; exact meanings vary by model.

How the F#-E# System Works

Jenn-Air shares the Whirlpool control platform, so it reports faults as two parts: an F number for the function group and an E number for the specific error within it. That makes the codes readable once you know the pattern, though the precise meaning can vary slightly by model, so confirm against your model number.

Control and Keypad: F1 and F2

F1 codes point to the control board or its memory, such as an EEPROM fault. F2 codes are keypad related, typically a stuck key where a button sticks or the membrane fails and the control reads a key as held. Both can sometimes be cleared with a power reset at the breaker for a few minutes. If either returns, the control board or keypad usually needs replacing.

Sensor and Latch: F3 and F5

F3 codes report the oven temperature sensor as open or out of range, so the oven will not heat safely until the sensor or its wiring is corrected. F5 codes report the door-latch system, common after a self-clean cycle if the latch motor or switch does not confirm its position. Let the oven cool fully first; a latch fault that persists cold needs service. These are defined oven repairs.

Common Codes at a Glance

CodeMeaningResponse
F1-E0 / F1-E1Control board / memory faultReset; replace control if it returns
F2-E0Stuck key / keypad faultReset; replace keypad if it returns
F3-E0 / F3-E1Oven sensor open or shortedTest and replace sensor
F5-E0 / F5-E1Door-latch faultCool fully; service latch
Recurring codeConfirmed component faultProfessional diagnosis
Write the whole code down. Both parts, like F3-E0, plus your model number, let us confirm the fault and bring the right sensor, keypad, or latch on the diagnostic visit.

Code Keeps Returning?

Book a brand-focused diagnosis for your Jenn-Air. Diagnostic and travel fees, if applicable, are confirmed before the appointment and before repair approval.

Frequently Asked Questions

What Does F2-E0 Mean on a Jenn-Air Oven?
F2-E0 is a stuck-key or keypad fault. A sticking button or a failing membrane makes the control think a key is held. Sometimes a power reset clears it; if it returns, the keypad or control needs replacing.
My Jenn-Air Shows F3-E0 and Will Not Heat. What Is It?
F3-E0 indicates an oven temperature sensor that is open or out of range, so the control will not heat safely. The sensor or its wiring needs to be tested and usually replaced.
What Is an F5 Code on a Jenn-Air Oven?
F5 codes point to the door-latch system, often after a self-clean cycle. The latch motor or switch is not confirming its position. Let the oven cool fully; if the latch fault stays, it needs service.

Related Reading

Jenn-Air Cooktop Troubleshooting

Burner and element problems.

Jenn-Air Maintenance Guide

Prevent the common faults.

Jenn-Air Repair

Models and problems we service.

Book a Repair in the Loveland Area

Detailed model and symptom intake, genuine OEM parts, and written warranty terms across Loveland and the Colorado high country.

Service Planning in Loveland

Service requests from Loveland, Berthoud, Johnstown, Erie commonly begin with an appliance not working, not cooling, not closing, leaking, or displaying an error. Share the model and exact symptom so the visit can be planned accurately. ZIP codes commonly served include 80537, 80513, 80534, 80516, 80517, 80620.

Call TodayRequest Service